Is there an Exchange 2013 DoD/Federal Message Clean/Spill Procedure?
I have seen DoD/Federal procedures to clean a message from early versions of Exchange (i.e. leakage/spill), but these procedures would not work for Exchange 2013.I know that in the past Microsoft has...
View ArticleFPE 2010 for Exchange
Dear All,we are currently using FPE 2010 for protecting our Exchange 2010 environment. We are moving with an exchange 2013 upgrade. After completing the upgrade we will have to replace the FPEs. What...
View ArticleSend connector not working for external emails
Hi - really hope someone can help, I am quite a novice at setting up Exchange so please bear with me. I have recently installed Exchange 2013, there was some initial failures due to old 2010 Exchange...
View ArticleSupport for TLS 1.2 over Exchange 2013?
How to enable TSL1.2 in Exchange 2013, any documentation leading me to configure it?Is there any confirmation about TSL 1.2 Supporting or not? Any help or insight would be greatly appreciated. Thanks!
View ArticleDrop messages in queue that have a blank sender
I'm getting hundreds of messages in the Queue where the From Address is < >. Do I just let these build up or is there a setting somewhere that would just drop the message if it has a blank...
View ArticleUnsubscribe link
Hi GuysPleas let me know if this can be achiveablewe have a requirment that every outbound email should have a Unsubscribe linkThe Unsubscribe link should be applicable only for external domainsAny...
View ArticleCan't send mail to AOL!
I have been trying to get mail flowing to AOL for months now.... I finally managed to figure out how to get an SMTP log from my send connector. The log contained the following:attempting to connect...
View ArticleWrong RejectMessage when using transport rule on exchange 2013 edge server
Hi,we are using Exchange 2013 SP1 (CU4) as an exchange edge server.We configured our domain with an spf text record which works fine for senderId. But senderId only recognizes the email address of the...
View ArticleExchange 2013 Catchall rules for specific domain
Hello - I have a secondary domain that I want to forward all emails from into a specific address. So I wrote a rule that I think should cover it:Apply rule if: The recipient address includes...
View ArticleDefault Frontend Receive Connector - Why is the "ExchangeServer" Auth...
I'm looking for clarification of the default mail flow behaviour of Exchange Server 2013 please. Basically, I'm having a hard time trying to understand why the "ExchangeServer" Auth Mechanism is...
View ArticleNew header from EOP: X-Microsoft-Antispam
I've noticed that we're receiving a new header in our e-mail coming through EOP with the text "X-Microsoft-Antispam." This appears to have started on May 31, 2014. We also saw a drop in Spam e-mail...
View ArticleAdd information to a Transport rule from CSV
I have a transport rule that will block internal employees from emailing certain external email address' and send a notification that the message was blocked from going out. That's working fine but I...
View ArticleClik here to view.
Slow mail flow?
Hi all!I installed Exchange 2013 CU1 on Server 2012. I have 2 2012 one for AD and one for Exchange. This is small enviroment, EX2013 has 8GB of RAM and 10 users on it. We recive around 150 mails per...
View ArticleTwo questions about Journaling and Queues
Hi, I've looked all over for this answer and I want to verify it. I've inherited an Exchange 2013 server and have to copy an overlarge journal DB off to PST and then delete it. That's fairly straight...
View Article451 4.7.0 Temporary server error. Please try again later. PRX2
I'm getting the dreaded "451 4.7.0 Temporary server error. Please try again later. PRX2" error when receiving SMTP mail.does anyone know exactly what causes this error? there are many references to it...
View Articleco-existence
I created my first test mailbox on exchange 2013, when I mail a user still on 2010 in our org it just goes to queue, in fact there is a bunch of stuff in there.The test account can however receive...
View Articlenext step in co-existence MAILFLOW
so I'm ready to change our firewall rule to route mail through 2013, exampleoldpublic 123.123.123.123 > 10.10.10.3Newpublic 123.123.123.123 > 10.10.10.4What do I need to do, do I remove the old...
View Articlesend connector and mail flow
I am co-existing between 2010 and 2013server 1 at Datacenter1server 2 at Datacenter2server 3 at Remote SiteIn my existing send connector I only have server 1 and server 2 however I just sent and email...
View ArticleExchange 2010 - The certificate status could not be determined because the...
I have tried everything I have found online to get my DigiCert to work.I have exported the cert and imported it into my child domains and they look perfect.It is just my parent domain having...
View ArticleHow to remove the GenerateIncidentReport action from a transportation rule
In Office 365 how do you remove the Generate Incident Report action from a rule? We enabled the reports during troubleshooting and now I would like to remove it from some of the rules. If I click the X...
View Article